How to Read a Food Packaging Bag Specification: A Field Guide to Every Parameter
A detail spec sheet should content which date?
A data specification sheet for Food Packaging Bags is, in essence, a "technical ID card" that defines packaging performance through quantitative metrics. It translates vague requirements—such as "durability," "freshness preservation," and "safety"—into measurable, verifiable physical and chemical values, playing a pivotal role throughout the entire lifecycle from production to end-use.

1. The material structure code
A structure like PET12/AL7/PA15/RCPP70 is read from the outside in, and the number after each material is its thickness in microns.
● PET 12- clear polyester, 12 microns, the standard print base: mechanical strength, printability, heat resistance.
● AL 7 - aluminium foil at 7 microns, the barrier layer, and the most common thickness in stand-up pouches.
● PA 15 - nylon, 15 microns, the abuse and puncture layer.
● RCPP 70- the retortable cast polypropylene sealant, 70 microns, which touches the food and does the sealing.
Unit trap: 12 microns equals 0.48 gauge, and 100 gauge equals 1 mil, or 25.4 microns. Suppliers quoting gauge and buyers reading microns are one decimal point away from a rework. And remember that a declared structure is not a delivered structure - a supplier can quote PET12/AL7/PA15/RCPP and only the retort test tells you what actually arrived.
2. Thickness, gauge and yield
Total thickness in microns is not enough. Ask for each layer's thickness, because a 100-micron structure can be built several ways and the performance differs. Yield, usually quoted in square metres per kilogram, is derived from thickness and density - which is why two films of identical thickness can deliver different bag counts per kilogram. Cost per thousand bags is the only thickness conversation worth having.
3. Barrier: OTR and WVTR
Oxygen transmission rate (cc/m2/day) and water vapour transmission rate (g/m2/day) are the two figures most often quoted without context. Both are steady-state rates measured under specified temperature and humidity - a number without test conditions is not a specification.
● Oxygenis typically measured by ASTM D3985, which uses a coulometric sensor to determine oxygen transmission through film and sheeting.
● Moistureis commonly measured by ASTM F1249.
Dry-goods shelf life is usually modelled on 23 degrees C and 50 percent relative humidity; humid or tropical distribution specs are quoted at higher humidity and temperature. For retort or pasteurized products, insist the barrier be measured after the process: heat, moisture and pressure change the numbers.
4. Seal parameters - where lines fail
Seal strength is quoted in N/15 mm, but the value means nothing without dwell time, temperature, pressure and jaw geometry. Typical datasheet values: a food-grade BOPP may target at least 1.5 N/15 mm measured after cooling; a high-speed BOPP grade may quote 5-7 N/15 mm at 0.5 second sealing with hot tack initiation at 110 degrees C; a barrier PE sealant for liquid stand-up pouches may run to 30 N/15 mm.
Three companion figures matter as much:
● Seal initiation temperature- the jaw temperature at which a defined seal strength is reached. Datasheets often define it as the point where seal strength reaches 4.0 N/15 mm.
● Hot tack- seal strength while still molten. This, not final seal strength, sets how fast you can fill.
● Sealing window- the temperature band between a weak seal and a burnt one. A narrow window is a productivity problem, not a technicality.
The failure that matters in practice is seal-through-contamination: grease, powder or liquid in the seal area destroys bond strength regardless of what the datasheet promised.
5. Mechanical parameters
Tensile strength in MD and TD (in MPa), elongation at break, and modulus describe how the web behaves under tension and how much it stretches during printing and lamination. Elmendorf tear, dart drop and puncture resistance describe what happens when the pack meets a sharp edge or a rough handler. Flex-crack or Gelbo testing predicts how barrier survives repeated folding - a plain barrier figure can halve after a journey. Lamination bond strength, also in N/15 mm, should exceed the seal strength of the structure, or the pack delaminates instead of opening.
6. Running parameters
Coefficient of friction, static and kinetic, is measured by ASTM D1894 using a weighted sled pulled across the film. It is the parameter that decides machine speed, web tracking and registration stability, and it changes with slip additives in the sealant. Ask also for blocking tendency, web width tolerance, roll diameter and core size.
7. Food-contact parameters
Overall migration limit is the headline number: under Regulation (EU) 10/2011, plastic materials and articles may not transfer constituents to food simulants in quantities exceeding 10 milligrams per dm2 of food contact surface, with 60 mg/kg of food as the equivalent expression. Specific migration limits apply substance by substance.
Ask for the declaration of compliance for the finished structure, the specific migration data for any substance of concern, residual solvent figures in mg/m2 with the test method named, and a PFAS statement. PFAS restrictions on food-contact packaging arrive with the EU packaging regulation from August 2026, so a coat that solved grease yesterday may be a compliance problem tomorrow.
8. Sustainability parameters now on the sheet
Post-consumer recycled content as a percentage, recyclability assessment and grade, mono-material share, whether the fitment, coating and adhesive sit in the same polymer family, and any compostability certification naming the finished structure rather than the film.

The data specification sheet plays a role throughout every stage of food packaging—from its inception (design) and manufacture (production) to its trade (procurement), use (packaging), and verification (quality inspection and shelf-life assessment). It serves simultaneously as a technical document, a management tool, and a commercial contract.
If you have any enquiry of the packaging bag and Film Roll, feel free to contact us to get a quotation!
